Page 3: Garage door opener lights, Motion sensor, Light feature, Timer-to-close (ttc), Lock, Battery backup only, Maintenance alert (mas)
Error Code 4-4 Liftmaster Model 8550w-267 User Manual Pdf
After our garage was burgled because we forgot to close a garage door, I replaced a fully working old Genie Pro Belt model with the Liftmaster 8550W, so we could get the auto-close feature that I'm happy with on our other lift-master chain drive opener.
3
Operation
PUSH BAR
Press the push bar to open or close the door.
NAVIGATION BUTTONS
Use the navigation buttons to make selections
and program features.
GARAGE DOOR OPENER LIGHTS
Press the LIGHT button to turn the garage door
opener lights on or off. When the lights are
turned on they will stay on until the LIGHT button
is pressed again, or until the garage door opener
is activated. Once the garage door opener is
activated the lights will turn off after the specified
period of time (the factory setting is 4-1/2
minutes). The LIGHT button will not control the
lights when the door is in motion.
Push Bar
LIGHT
Button
Screen
Motion
Sensor
Navigation
Buttons
The TTC feature will deactivate if the garage door
encounters an obstruction twice; or the safety
reversing sensors are incorrectly installed. The
garage door will reverse open and WILL NOT
close until the obstructions are clear or the safety
reversing sensors are correctly installed. When
the obstruction has been cleared or the safety
reversing sensors have
been aligned, the door
will close when the
garage door opener is
activated.
To temporarily suspend the TTC feature press
and release the HOLD button. Press REL button
to resume normal TTC
operation.
TIMER-TO-CLOSE (TTC)
DO NOT enable TTC if operating a one-piece
door. TTC is to be used ONLY with sectional
doors.
Once the TTC has been set and the door is open,
the selected close interval will be displayed on
the screen and toggle between the time and TTC
message. The garage door opener will beep and
the lights will flash before closing the door.
When the TTC is on the
following message will
display on the door
control:
TO REMOTE
BATTERY BACKUP ONLY
If your garage door opener has a battery backup
one of the following messages will display on the
door control if there is a problem with the
battery:
MAINTENANCE ALERT (MAS)
When the maintenance alert is on and the garage
door opener needs maintenance the following
message will display on the screen:
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
Program
Press the button on the remote
control that you wish to operate
your garage door.
Enter a 4-digit personal identification
number (PIN) of your choice on the
keyless entry keypad. Then press the
ENTER button.
PIN
?
?
?
?
1
2
Error Code 4-4 Liftmaster Model 8550w-267 User Manual 2017
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PRS
8
TUV
9
WXY
0
QZ
*
#
ENTER
0 QZ
*
#
ENTER
OR
4a
4b
Error Code 4-4 Liftmaster Model 8550w-267 User Manual Transmission
Press the navigation
button below 'MENU' to
view the Features menu.
Select 'REMOTE' or 'KEYPAD'
to program from the program
menu. Press
to continue.
1
3
2
The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.
Repeat the steps above for programming additional remote controls or keyless entry devices. If programming is unsuccessful, refer to the remote control instructions.
MOTION SENSOR
This feature will automatically turn on the garage
door opener lights when motion is sensed. The
lights will come on for the set period of time,
then shut off.
Liftmaster Model Numbers
LIGHT FEATURE
The lights will turn on when someone enters
through the open garage door and the safety
reversing sensor infrared beam is broken.
If using the garage door opener light as a work
light, turn the light on using the light button on
the wall control or the light will turn off if you are
beyond the range of the sensor.
LOCK
When the Lock feature is on, your remote
controls have been disabled and the following
message will display on the door control:
Error Code 4-4 Liftmaster Model 8550w-267 User Manual Free
Use the navigation buttons to
scroll to 'PROGRAM' and
press the navigation button
under
Error Code 4-4 Liftmaster Model 8550w-267 User Manual 10
to continue.