Page 19: Replacement parts and accessories, Continued
Find many great new & used options and get the best deals for Remington Electric Pole Saw/Chainsaw Combo 10 in. Bar/Chain 8 Amp (2-in-1) at the best online prices at eBay! Free shipping for many products!
111409-01 Remington Polesaw Branch Wizard replacement parts and part list for 111409-01 Remington electric Branch Wizard polesaws by Desa International You have no items in your shopping cart. Thank you for choosing PartsFor.com. PartsFor.com is a national parts distributor serving the continental US. Operation and use Remington RM1015P Branch Wizard Plus Review. Remington Tools 8 Amp 1.5 hp 10' Electric Pole Saw. $109.99 Remington RM1015P 2-in-1 Electric Chain Saw/Pole Saw Combo / 41AZ22PG983. An electric pole saw will save you hours of ladder work. A manual pole pruner might be all you need for pruning small branches.
19
111607
www.desatech.com
3. Press 5/32' round file (attached to file guide) into
groove between top plate and depth gauge on
chain. File guide should rest on both top plate
and depth gauge (see Figure 15).
Note:
File at
midpoint of guide bar.
4. Hold file guide level. Make sure 30
° mark on
file guide is parallel to center of guide bar (see
Figure 15). This will insure that you file cutters
at 30
° angle.
5. File from inside towards outside of cutter until
sharp. Only file in this one direction (see Figure
15).
Note:
Two or three strokes with file should
sharpen cutter.
6. After each cutter is sharpened, move chain for-
ward to sharpen next cutter. File all cutters on
one side of chain.
7. Move to other side of chain and repeat process.
Filing Cutter Depth Gauges
The cutter depth gauge clearance is reduced as cut-
ters are sharpened. After every second or third sharp-
ening, reset cutter depth gauges.
1. Place depth gauge tool (.025') firmly across top
of two cutters. Make sure depth gauge enters slot
in depth gauge tool (see Figure 17).
2. Use medium flat file. File depth gauge level with
depth gauge tool.
3. Remove depth gauge tool. With flat file, round
off front corner of cutter depth gauge (see Fig-
ure 18).
After several hand filings, have authorized service
center or sharpening service machine sharpen chain.
This will insure even filing.
REPLACING SAW CHAIN
Replace chain when cutters are too worn to sharpen or
when chain breaks. Only use replacement chain noted
in this manual. Always include new drive sprocket when
replacing chain. This will maintain proper driving of
chain.
Note:
For proper chain and drive sprocket, see
Replacement Parts and Accessories.
STORAGE
If storing Pole Saw for more than 30 days, follow
steps below.
1. Remove and clean guide bar and chain. Clean
guide bar and chain by soaking in petroleum
based solvent or mild soap and water mixture.
2. Dry guide bar and chain.
3. Place chain in container filled with oil. This will
prevent rust.
4. Wipe a thin coating of oil over surface of guide bar.
CLEANING AND
MAINTENANCE
Continued
TECHNICAL SERVICE
You may have further questions about assembling,
operating, or maintaining this product. If so, you can
visit our Technical Service web site at
www.desatech.com
or contact our Technical Ser-
vice Department at 1-800-858-8501 (English Only).
You may also write to:
DESA Specialty Products™
P.O. Box 90004
Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
When contacting DESA Specialty Products™, have
ready
• Your Name
• Your Address
• Your Phone Number
• Model Number of Product
• Date of Purchase (Include copy of receipt for
written requests).
REPLACEMENT PARTS
AND ACCESSORIES
WARNING: Use only replacement
parts and accessories described in this
manual. Use of other parts or accessories
could damage saw or injure operator.
5. Wipe off outside of Pole Saw body. Do this with
soft cloth dampened with a mild soap and water
mixture.
6. Store Pole Saw
• in a high or locked place, out of children’s reach
• in a dry place
• with scabbard over guide bar
For original replacement parts and accessories, con-
tact your nearest Authorized Dealer or Authorized
Service Center for this product. If they can not sup-
ply the part or accessory, contact your nearest Parts
Central listed on page 36. Each Authorized Dealer,
Authorized Service Center, and Parts Central is in-
dependently owned and operated.
See pages 34 and 35 for an Illustrated Parts List.
If you need additional referral information, contact
our Technical Service Department (see Technical
Service, page 19).
In Canada call 1-800-561-3372 for parts information.
Model 111607-01
Part Number
Description
110413-01S
Guide bar, 6' (15.2 cm)
111372-01S
Chain, 6' (15.2 cm)
Remington Branch Wizard Plus Rm1015p Parts
111363-01
Drive Sprocket